MAXTECH CORPORATION XPS 288IR (SF-1128HV/R16-PNP) Card Type Modem, Fax Chip Set Unidentified I/O Options Line in, line out, microphone in, speaker out Maximum Modem Rate 28.8Kbps Maximum Fax Rate 14.4Kbps Data Modulation Protocol Bell 103/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 Fax Modulation Protocol ITU-T V.17, V.27ter, V.29 Error Correction/Compression MNP5, V.42, V.42bis Fax Class Class I & II Data Bus 16-bit ISA Card Size Half-length, half-height card [Image] CONNECTIONS Function Label Function Label Line out CN1 Microphone in CN3 Line in CN2 Speaker out CN4 SUPPORTED COMMAND SET Basic AT Commands AT, ‘+++’, A/ A, B, E, H, M, O, P, Q, T, V, W, X, Y, Z &C, &F, &P, &T, &V, &W, &Y, &Z Extended AT Commands \A, \B, \K, \N %C, %L, %Q S Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25, S26, S27, S29, S30, S31, S32, S33, S36, S37, S38, S39, S40, S41, S46, S48, S82, S86, S91, S92, S95 Special Commands #BDR, #CID=n, #CID?, #CID=?, #MDL?, #MFR?, #REV?, #TL, #VBQ?, #VBS, #VBT, #VCI?, #VLS, #VRA, #VRN, #VRX, #VSDB, #VSK, #VSP, #VSR, #VSS, #VTD, #VTM, #VTS, #VTX, +MS Note: See MHI Help File for full command documentation. Proprietary AT Command Set AUTOSCAN MODE Type: Immediate Format: AT [cmds] Nn [cmds] Description: Enables/Disables Autoscan mode Command Function N0 Autoscan mode disabled í N1 Autoscan mode enabled COMMUNICATIONS MODE Type: Configuration Format: AT [cmds] &Mn [cmds] Description: Selects communications mode Command Mode &M0 Asynchronous mode COMMUNICATIONS MODE (DATA LINK AND FALLBACK) Type: Configuration Format: AT [cmds] &Q [cmds] Description: Configures data link options Command Function &Q0 Set Direct data link only &Q5 Set V.42 data link with fallback options &Q6 Set Normal data link only CTS Type: Configuration Format: AT [cmds] &Rn [cmds] Description: Configures CTS settings Command Function &R0 Reserved í &R1 Enables CTS operation based on flow control settings DATA SET READY (DSR) Type: Configuration Format: AT [cmds] &Sn [cmds] Description: Selects DSR options Command Function &S0 DSR forced high &S1 DSR is off while in command mode and set on in on-line mode DATA TERMINAL READY (DTR) Type: Configuration Format: AT [cmds] &Dn [cmds] Description: Selects modem response to DTR Command Function &D0 Modem does not respond to DTR &D1 Modem goes to command mode after DTR goes is off &D2 Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled. &D3 Modem is initialized after DTR goes off DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials telephone number according to any modifiers included in the string Note: Any combination of modifiers can be used to produce the desired dial functions in sequence. Command Function DL Re-dial last number DP Pulse dialing enabled í DT Tone dialing enabled/Pulse dialing disabled DW Dialing resumed following dial tone detection D, Dialing paused for amount of time specified in S8 register D"WXY" Optional method of denoting telephone numbers. Letters enclosed in quotes are interpreted as numbers according to the system found on a telephone keypad. D! Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. D@ Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. D; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. FLOW CONTROL Type: Immediate Format: AT [cmds] &K [cmds] Description: Configures flow control settings Command Function &K0 Flow control disabled &K3 RTS/CTS hardware flow control enabled &K4 XON/XOFF software flow control enabled &K5 Transparent XON/XOFF software flow control enabled &K6 RTS/CTS & XON/XOFF flow control enabled GUARD TONE Type: Configuration Format: AT [cmds] &Gn [cmds] Description: Enables/Disables and configures guard tone Command Function í &G0 Guard tone disabled &G1 Guard tone disabled &G2 Set guard tone at 1800Hz HAYES SMARTMODEM 300 COMPATIBILITY Type: Configuration Format: AT [cmds] Xn [cmds] Description: Configures modem response and blind dialing capabilities Command Function X0 Sets modem to use Hayes Smartmodem 300 responses and blind dialing X1 Sets modem to use Hayes Smartmodem 300 responses, CONNECT responses, and blind dialing X2 Sets modem to use Hayes Smartmodem 300 responses, CONNECT responses, dial tone detection, and blind dialing X3 Sets modem to use Hayes Smartmodem 300 responses, CONNECT responses, busy detection, and blind dialing í X4 Set modem to use all responses, dial tone detection, and busy signal detection LINE TYPE Type: Configuration Format: AT [cmds] &Ln [cmds] Description: Selects line type Command Line Type &L0 Switched line (PSTN/Dial-up) REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I0 Reports product ID I1 Reports ROM checksum I2 Tests and reports internal memory I3 Reports firmware ID I4 Reports reserved ID SPEAKER VOLUME Type: Configuration Format: AT [cmds] Ln [cmds] Description: Controls speaker volume Command Function L0 Low volume setting L1 Low volume setting L2 Medium volume setting L3 Highest volume setting Extended AT Commands AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD Type: Configuration Format: AT [cmds] %En [cmds] Description: Controls auto-retrain mode and fallback/fall-forward Command Function %E0 Auto-retrain disabled %E1 Auto-retrain enabled CONNECT MODE Type: Configuration Format: AT [cmds] \Nn [cmds] Description: Configures data link and fallback options Command Function \N0 Set Normal data link only \N1 Set Direct data link only \N2 Set V.42 or MNP data link only í \N3 Set V.42/MNP/Normal data link \N4 Set V.42 data link only \N5 Set MNP data link only